收藏本站
144
JACKS AND PLUGS
.173" MINIATURE TELEPHONE PLUGS BANTAM TYPE PHONE: 773 792-2700
* Please visit the product pages on our website for the most up-to-date product information
.173" MINIATURE TELEPHONE PLUGS BANTAM TYPE
FEATURES
Miniature telephone twin plugs with two 2-conductor or two
3-conductor fingers, designed to mate with TT Twin-Jax ? ,
TT-Jax ? , and other phone jacks with a .176" inside diameter
bushing and compatible tip and ring springs. Approximately
1/2 the size of standard phone plugs; yet retains uniformity,
dependability of high-quality phone plugs. The phone plugs
are exceptionally light, small and rugged. Plug fingers can
easily be removed and replaced.
? Minimum Space: Plugs fit .313" centers, horizontally
or vertically.
? Self-Aligning: Plug fingers compensate for minor
variations in jack spacing.
? Polarizing: Handle notches identify location of each finger.
? Tip Monitoring: Handle ports permit probe insertion to
monitor tip circuits.
? Terminating and Looping Plugs: OEMs can fabricate
cross-wired plugs, i.e., tip-to-sleeve, tip-to-ring, etc.,
according to individual requirements. OEMs can also
wire-in resistors, RCL networks, etc. for standard and
special terminating applications. Switchcraft will build
looping and terminating TT-Twin Plugs on special order,
where quantities warrant.
? Sleeve Plugs: For looping, terminating and single cable
applications, sleeve plugs seal off unused handle open-ing(s).
Sleeve plugs also make a bridged (common) sleeve
connection by holding braided shield in place in second
plug.On special order, TT-Twin Plugs can be supplied
with one 2-conductor finger and one 3-conductor finger.
TT263
TT261
TT261
TT263
TT263: 6-circuit plug consists of two electrically-independent
3-conductor fingers with black handle. Can use single or dual
cables for two electrically-independent 3-conductor fingers or
common tip, ring and/or sleeve circuits.
? Ease of Assembly/Disassembly: Refer to illustration below
for assembly/disassembly procedure; no handle retaining
screws required. Tip and ring terminations are screw-type
Typical
Part Mating
Number 1 Cond. Terminals Jack 2
Handle
Handle
Part
Number
MIL Type
Number
screws supplied).
SPECIFICATIONS
TT261
TT263
2
3
Screw 3
TT31
TT32B
Black
Black
T2300-2
T2316
–
M642/13-3
Tip Rod, Ring, Sleeve and Body: Copper alloy,
natural finish.
Terminals and Terminal Screws: Copper alloy,
natural finish.
Insulation: Thermoplastic.
1. TT-Twin Plug plugs can be supplied with one, 2-conductor plug finger and
one, 3-conductor plug finger in the same handle (on special order).
2. Switchcraft Part Numbers. See additional mating jacks in this section.
3. Switchcraft Replacement screw P2240 , Terminal P2642 . 2 each required
with 2-conductor twin plugs; 4 each required with 3-conductor twin plugs.
4. Replacement Hole Plug Switchcraft T2318 (Black) T2319 (Red).
Handle, Sleeve Plugs: Molded plastic.
1. DISASSEMBLY: Place plug on edge as shown. Push down
1.
NOTCH
2. & 3.
LIP
BRAIDED
SHIELD
and back on metal lip on finger (inside notch) with small
screwdriver and slip plug finger out of handle. Turn plug
FINGER
over and repeat for other finger.
2. CABLE INSTALLATION: Fold braided shield on cable back
4.
LIP ON
FINGER
NOTCH
over insulation. Insert leads through rear of plug finger, and
screw finger (clockwise) onto cable with twisting motion
until lead terminations lineup with threaded tip and/or ring
openings. Fasten terminals on both fingers with screws
provided.
3. To bridge sleeves (common connection), place free end of
GROOVE
INTERNAL RIB
braided shield in remaining finger sleeve opening. Press
sleeve plug firmly in place.
TT261: Two electrically-independent 2-conductor fingers in a black
handle. Can be used with single or dual cables for independent tip
circuits with common sleeve or separate sleeve circuits.
4. ASSEMBLY: Align grooves in fingers with internal handle
ribs and insert fingers into rear of handle. Push fingers in
until lips or rear of fingers snap into notches on handle.
DIMENSIONS ARE FOR REFERENCE ONLY
www.switchcraft.com
Inch
(mm)
? Registered trademark of Switchcraft, Inc.
Note: Contact your Switchcraft Representative for price and delivery
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
236PKG CONN PLUG AUDIO PHONE R/A 3 COND
238 CONN PLUG FLAT 3COND SOLDER LUG
242102 CONN ADT SMA PLUG-BNC JACK
242103 CONN ADT SMA JACK-BNC PLUG
242105RP CONN ADT SMA JACK-TNC R/P PLUG
242107RP CONN ADT SMA JACK-TNC R/P JACK
242112RP CONN ADT SMA R/P PLUG-N JACK
242113RP CONN ADT R/P SMA JACK-N PLUG
相关代理商/技术参数
2332BG 制造商:Aavid Thermalloy 功能描述:35683 制造商:Aavid Thermalloy 功能描述:- Bulk 制造商:Aavid Thermalloy 功能描述:Aavid Internal P/N:035683
2332B-TACHG 功能描述:散热片 41.3X43.2X16.5 BGA BLACK ANODIZE RoHS:否 制造商:Ampro By ADLINK 产品:Heat Sink Accessories 安装风格:Through Hole 散热片材料: 散热片样式: 热阻: 长度: 宽度: 高度: 设计目的:Express-HRR
2332BX 功能描述:电话连接器 DUAL JACK BLOCK RoHS RoHS:否 制造商:Switchcraft 标准:1/4 in 开关配置:Switched 型式:Female 位置/触点数量: 端接类型:Solder 安装风格:Chassis (Panel) 方向:
2332-CLC 制造商:Platt Luggage 功能描述:
2332D5 功能描述:面板安装指示灯 GREEN DIFFUSED RoHS:否 制造商:Chicago Miniature 产品:Oil-Tight Non-Relampable Neon LED Indicators 灯类型:Neon 灯座类型:Wire Terminal 工作电压:105 VAC to 125 VAC 封装:Bulk
2332DX5 功能描述:面板安装指示灯 RECT PMI W/TERM BK BZL RoHS:否 制造商:Chicago Miniature 产品:Oil-Tight Non-Relampable Neon LED Indicators 灯类型:Neon 灯座类型:Wire Terminal 工作电压:105 VAC to 125 VAC 封装:Bulk
2332-L 制造商:Milwaukee Electric Tool Corporation 功能描述:M12 REALTREE AP HEATED JACKET LARGE 制造商:MILWAUKEE TOOL 功能描述:M12 REALTREE AP HEATED JACKET LARGE
2332NM 制造商:Thomas & Betts 功能描述: